国产亚洲精品精品精品_国产精品人人做人人爽_天天爽夜夜爽人人爽_国产微拍精品一区二区

歡迎來到,深圳市芬德電子科技有限公司官網!

finder功率繼電器

聯系電話:0755-84552800

手機號碼:189-2606-1910

News
熱門搜索: Motor automation equipment、 Enclosure、 Product 40 series、 55 series、 38 series、 Series 80...

News

Shenzhen Fende Electronic Technology Co., Ltd

Address: d1001, Vanke building, No. 7188, Longxiang Avenue, Longgang District, Shenzhen

Tel: 0755-84552800/01/02/03
Fax: 0755-0755-28891512

Email:sales@ff-energy.com

Industry trends

Correct use of finder relay

文章出處:芬德電子科技 / 作者:芬德電子科技 / 發表時間:2022-03-22

1. Selection of rated working voltage of finder relay

The rated working voltage of finder relay is a very important technical parameter of relay. When using a relay, first consider the working voltage of the circuit where the relay coil is located, and the rated working voltage of the relay should be equal to the working voltage of the circuit. The working voltage of general circuit is 0.86 of the rated working voltage of relay. Note that the workpiece voltage of the circuit should not exceed the rated working voltage of the relay, otherwise the finder relay coil is easy to burn out. In addition, some integrated circuits, such as NE555 circuit, can directly drive the relay, while some integrated circuits, such as COMS circuit, need to add a transistor amplification circuit to drive the relay if the output current is small, so it should be considered that the output current of the transistor should be greater than the rated working current of the relay.

40系列.jpg

2. Selection of contact point load

Contact point load refers to the bearing capacity of the contact point. The contact of finder relay can bear a certain voltage and current during switching. Therefore, when using finder relay, it should be considered that the voltage applied to the contact and the current through the contact should not exceed the contact load capacity of the relay. For example, the contact load of a relay is 28V (DC) × 10A, indicating that the finder relay contact can only work on the circuit with DC voltage of 28V, and the contact current is 10A. If it exceeds 28V or 10a, it will affect the normal use of the finder relay, and even burn out the contact.


3. Selection of coil power supply of finder relay

This refers to whether the finder relay coil uses direct current (DC) or alternating current (AC). Generally, beginners will use electronic circuits in electronic production activities. Electronic circuits are often powered by DC power supply, so finder relays with DC voltage coil must be used.

桂东县| 汝阳县| 郧西县| 阳朔县| 汉川市| 独山县| 家居| 皮山县| 蒙山县| 仙游县| 江陵县| 临清市| 吴忠市| 寻乌县| 洪湖市| 富蕴县| 新丰县| 营口市| 乌鲁木齐市| 桂阳县| 清丰县| 闻喜县| 榆社县| 绥德县| 白沙| 建始县| 泰州市| 胶南市| 金寨县| 翼城县| 巢湖市| 广东省| 昌江| 韶山市| 安阳市| 奎屯市| 新干县| 邵东县| 凤凰县| 资兴市| 舞阳县|